Commercial Door Installation

Commercial drywall frames are offered in knockdown form or welded and can be engineered to meet specific architectural requirements for a wide range of uses.

Specifications:

  • 18 gauge (1.2) or 16 gauge (1.5) galvanneal steel
  • For use with 1 1/4" (45) doors (steel or wood)
  • Available jamb sizes from 4 1/2" up to 12 3/4"
  • Prepared for 9/32" silencer holes
  • All jambs complete with base and center strap anchors and an adjustable top tension anchor

20 Gauge for 1-3/8" Door

Commercial frames are designed with overlapping mitred corners for a clean and accurate finish. The rabbet width and height are oversized to accept standard size 1 3/8" hollow core wood doors with minimal machining requirement.

Specifications:

  • 20 gauge (.76) galvanneal steel
  • For use with 1 3/8" (38) doors
  • Available in wall sizes: 2 5/8" 3 1/2", 4 5/8" and 4 7/8"
  • Prepared for 3/16 silencer holes (silencers included)
  • All jambs complete with base and center strap anchors and an adjustable top tension anchor
    All frames prepared and supplied with one pair of 3 1/2" x 3 1/2" hinges C4 finish
    All strike jambs prepared for colonial or standard slab door

EXPANDABLE DRYWALL FRAMES

Commercial drywall frames offer optimum versatility due to its unique design with over 3 inches of expansion to accommodate various wall thicknesses. Frames are available knockdown for easy field installation after walls have been erected.

Specifications: 

  • 18 gauge (1.2) or 16 gauge (1.5) galvanneal steel
  • For use with 1 1/4" (45) doors (steel or wood)
  • Adjustable from 5 1/2" to 8 1/4"
  • Prepared for 9/32" silencer holes
  • Prepared to receive countersunk screws #7 x 2 1/2 (included)
  • Prepared with 12 gauge A.S.A. strike reinforcing
  • Prepared with 1 1/2 pairs of high frequency 10 gauge 4 1/2" hinge reinforcement
  • Height available: 6'8", 7'0" or 8'0"


  



Other options: Door frame and door installation instructions

Installation option 1:

1. Construct wall with rough opening height equal to finished opening height plus 1/4" to 1" max. Rough opening width is as follows:

(A) For 2" face frames: Opening width plus 2 1/8" to 2 3/8"

(B) For 1 3/4" and 1 1/2" face frames: Opening width plus 2"

2. If optional base anchor is used, notch drywall in that area.

3. Retract compression bars in the jambs by turning screws clockwise and install one jamb in position on the wall.

4. Insert frame head under the corner clips of the jamb and raise the head into position.

5. Insert the corner clips of the remaining jamb into the opposite end of the head and position jamb on the wall.

6. Locate a removable frame bar at sill of the frame to maintain proper opening width during installation.

7. Square and plume frame and install base anchor screws through countersink holes in frame face, and into floor plate.

8. Square top of frame and tighten compression bars by turning screws counter clockwise. (Do not over tighten).

9. Install (4) # 8 x 1/2" sheet metal screws at the corners of the head to attach head to jambs. (Mandatory for fire rated frames).


Installation option 2:

1. Place one of the vertical frames first to the door opening. Start by angling it at the base of the opening, then place it into position at the top of the     door opening.

2. Next, install the horizontal header frame above the first vertical frame column. Make sure you snap it into place and use a hammer if needed so it     interconnects with the first vertical frame column.

3. Next, install the last vertical frame column by placing it underneath the horizontal frame and then kicking it in the base below.

4. Once the full three piece frame is in place, install the hinges and door, then square up the bottom frame first and then put your level on the horizontal     header frame to level it up.

5. Once the door is installed, check the top of the door and both side of the door to make sure it's squared up and most importantly the door swings     smoothly.

6. Use adjuster screws to move the frames into a centered position, and check to make sure both vertical frame columns are plume. Once you have     everything squares and plume, and the spacing between the door, and door frames are even, and then install long screws into the base strap     anchors.



Buckhead Locksmith of Atlanta (404) 456-3817 Offers Commercial Door Installation Services!